Tuesday, December 11, 2012

Foam

I've not posted for while as I've been waiting on my spray foam contractor. The crew showed up last week, and ran out of material about 15/16's through the job. It took them another week to get back on site, but all is good now and the super structure is foamed. It was worth waiting on the foam contractor as he did the job  for less than I could buy the material and do it myself.

All the metal is covered and I started trimming the foam flush with the wood firing. I held the wood proud of the metal about 5/16 ", and that has proved to be enough as the foam is sticking to the metal as I trim it. If I hurry things, and try to pry a piece of foam off with my knife, it will pop off of the metal which will need to get another coating. My goal is to have no metal showing so the metal won't sweat. I'm afraid that if any metal is exposed, it will sweat and drip on to the finished interior. A worse case would be if I would get some copious sweating and cause some crevice corrosion to start behind the liner.


Now that I have the foam in and can see how the windows will install, I think my method will work just fine. I will have a small 5/8" shoulder to deal with on the aft bulkhead wall, but it won't be that big of a  deal as there are only two windows on that wall. For the man door on the aft bulkhead wall, I installed blocking 3/4" in from metal rough opening so I can install a solid wood jamb. The solid wood jamb will let me install a temporary door to keep her locked up  once I get her down to the launch site. I'm not  going to try to fabricate the finish doors until I have the hull and super structure out of the barn and I have some room to work.

The aft deck ceiling also received a coating of foam. Experience from owning heavy equipment has taught me that  metal roofs will start dripping heavy as the sun hits the cool metal in the morning. Again, I don't want any metal sweating on the boat.


Trimming the foam is kind of a pain, and is going slow. Having caught a case of the winter crud from the kids is also slowing me down. I guess the one of the kids dragged a bug into the house and it latched on to me. I feel like crap, but foam trimming must go on!!! My tool of choice is a fillet knife. Dull knives are one of my pet peeves  I keep an oil stone lubed up on the work bench and every ten minutes or so, I'll put an edge on he knife. The foam guys  had some long, skinny spatulas that they put an edge on, and that looked like it too would be a good  tool . Like I said above, the foam will pop off of the metal if you pry on it. Once I weld the super structure to the hull, I'll need to buy a small kit to foam the weld zones. I'll touch up any damaged areas at that time.

The weather has  turned to crap in these parts, with cold temperatures and lots of rain. I'm hoping the snow stays away again this winter, but I think I'm hoping for too much.  Because of the weather, and the speed I can get most of these jobs done while she's in the barn, I'm  in no hurry now to get the hull out of the barn.  I have plenty to keep me busy for another couple of months. and there is two years worth of fire wood split to keep the barn warm.  I'm still planning on moving her this winter, but I have to finish some jobs I have going on with contractors, and I have to deal with the holidays coming up.Once the holidays are over, I'll get more serious about getting her off of the hill.


 Cheers  

5 comments:

  1. I remember somebody working on trimming foam rigged up wire that they ran electricity thru to make it hot and it sliced the foam like butter.

    Just a thought.

    Bill Kelleher

    ReplyDelete
  2. My two favorite foam trimming tools are:
    1)a serrated bread knife and
    2)a scraper blade on a MultiMaster

    If you have the latter, try it.....effortless compared to a knife.

    Andre used a pneumatic oscillating sander (!!) - made a lot of dust, but left a good finish.

    ReplyDelete
  3. Greetings gents,

    The foam trimming is finished. I did try one of those high speed cutting tools, but the dust was too hatefull. I stuck with the razor sharp fillet knife. The power tool came in handy in spots where I could not get the knife square to the frame.

    ReplyDelete
  4. MDF - Eximcorp , Eximcorp India Pvt Ltd is a leading Wood & Wood panel products Plywood - Eximcorp



    ReplyDelete
  5. Hello,

    Wow so nice! A foam is used to hold a hot or cold beverage. Create a foam boat to entertain your child and teach him the importance of up cycling or making something new out of an unwanted object. Keep it working every day.






    ReplyDelete